These Crank Relearn Instructions may not apply to all vehicles. But they're close to how it's done on most cars.

• Engine Analyzer Pro
• Engine Analyzer Pro 3.9 Unlocking Codes
• Engine Analyzer Pro 3.9 Unlocking Code
• Engine Analyzer Codes
• Engine Code Analyzer Reviews
• Engine Analyzer Pro 3.9 Cracked

To perform the relearn, proceed as follows:
Connect a scanner to make sure there are no trouble codes stored in the computer’s memory.

If there is any power train trouble code other than P1336 (Crankshaft Position Variation not learned), the computer will disable the relearn function until the problem that caused the code has been eliminated.

Also, make sure that the engine coolant (check it when the engine is cold) and oil levels are at an acceptable level.

Performance Trends (www.performancetrends.com) offers three versions: Engine Analyzer, Engine Analyzer Plus, and Engine Analyzer Pro. All of them simulate almost any engine combination you can conceive, including bore and stroke sizes from 1 to 10 inches and up to 16 cylinders with multiple valves (2 to 6) and an RPM range from 500 to 30,000. The Engine Analyzer Pro is a comprehensive software package for the professional engine builder or engineer to simulate an engine build-up or modification. It let's you try various combinations of cams, Heads, intakes, superchargers, etc. And see the effect on torque, HP, air flow, fuel flow, maximum cylinder pressure, volumetric efficiency, etc. Free engine analyzer pro 3.9 download. Education software downloads - Engine Analyzer Pro by Performance Trends Inc and many more programs are available for instant and free download. If you want the engine only, you can get it through Homebrew: brew install stockfish. Note: The Stockfish chess engine is a command line program. You may want to use it in your own UCI-compatible chess GUI. Cheap Electrical Testers & Test Leads, Buy Quality Automobiles & Motorcycles Directly from China Suppliers:Engine Analyzer Pro v3.9 English Enjoy Free Shipping Worldwide! Limited Time Sale Easy Return.

1. Set the parking brake and block the drive wheels. Make sure that the hood is closed.
2. Start the engine and make sure that the engine coolant temperature is at least 158 degrees F. (70 degrees C.)
3. Turn the engine off for at least 10 seconds.
4. Select the crankshaft position variation learn procedure (CASE Learn)on your scanner.
5. Make sure that the transmission is in Park. Start the engine.
6. Apply the brakes and hold the pedal firmly.
7. Follow the scanner instructions.

Engine Analyzer Pro

Remember: That you are going to increase the engine speed to approximately 3000 RPM, 4000 RPM, or 5150 RPM. That’s the variation learn fuel cutoff RPM (depending upon the engine), and that it’s important to release the throttle when the engine RPM starts to decrease as a result of the fuel cutoff going into effect. Failure to do such will result in over revving of the engine, causing possible engine damage.

8. Once the engine has returned to idle, check the status of Diagnostic trouble code P1336. If the scanner indicates that the CASE has been learned, the relearn procedure is now complete. If CASE has not been learned, check for the presence of other power train codes. If any exist, correct the problem, then repeat this procedure.

NOTE: If the Crankshaft Variation Relearn is not accessible through your scanner (some truck applications 1998 & later), perform the relearn in the following manner:

1. Turn off all of the accessories. With the Air temperature sensor and Coolant temperature within 5 degrees (Centigrade) of each other, start the engine and let it idle in Park or Neutral for two minutes.
2. Accelerate the vehicle to 55 mph at part throttle. Cruise at 55 mph for 8- 10 minutes until the engine reaches operating temperature.
3. Cruise at 55 mph for another 5-6 minutes.
4. Decelerate to 45 mph without using the brakes, and maintain 45 mph for 1 minute.
5. Perform 4 deceleration cycles, without using the brakes, of 25 seconds each where no specific speed is necessary. Returning to 45 mph for 15 seconds in between deceleration cycles.
6. Accelerate to 55 mph and cruise for 2 minutes.
7. Stop the vehicle and idle for 2 minutes with the brake applied and the transmission in Drive (automatic trans.) or Neutral (manual trans.) with the clutch depressed.

Engine Analyzer Pro 3.9 Unlocking Codes

Engine Analyzer Pro 3.9 Unlocking Code

Engine Analyzer Codes

Engine Code Analyzer Reviews

Engine Analyzer Pro 3.9 Cracked